Brewery 20HL 3-vessel

915.000 DKK excl. vat

20HL 3-vessel brewing unit (brewhouse)

A 3-vessel brew house as the basic configuration, which make 2 brews an a workday without any problem. The system is also flexible for both infusion and decoction brewing.

Basic configuration:

  • 2.000L mash tun
  • 2.000L lauter tun
  • 2.000L kettle/whirlpool tank
  • Plate Heat Exchanger

A optional hot water tank (HLT) prepares hot water for both 1st and 2nd brews.
Continuous brewing is more convenient. For instance can the second mashing start during the 1st lautering process. This saves time spent on mashing process.
The hopback filter is configured to avoid any potential sucking problem on heat exchanger. There might be some solid material left after whirlpool progress.

Heat exchanger spec will be defined as the actual brew data like wort/water inlet/outlet temperature etc.

The brewery section demands about 6 x 12 meter space – about 4-5 meter to the ceiling depending on the demands for grain handling equipment.

Steam jacket for mash tun and kettle tun. Jacket installed on both cylinder and bottom section. The jacket can separated in zones and controlled separately, so small batch brewing is possible.
A buffer tank configured to avoid vacuum problem during lautering process.

Mash tun equipped with bottom agitator with VFD control- Paddle type stir for better mixing of water and malt. The bottom stir lowers the twist force of when it is working, which is a normal and more reasonable design tank with such capacity. Stir speed to be adjustable.

Lauter tun equipped with bottom agitator, VFD controlled, to lower the twist force and extend the tanks using life. Lauter tun equipment with grain spending unit, with bottom spent grain door, the grain outlet could be a knife or flange gate valve.

A buffer tank configured to avoid vacuum problem during lautering process.

A console configured for checking the wort.

This is only the basic unit for brewing. Please check the following items for a complete brewhouse:

Not in stock. Ask for delivery time

Description

2000 liter Mash tun 1 pcs.

  • Design pressure: Atmospheric
  • Material: AISI 304
  • Total volume: 3500 liter, effective volume: 2.000 liter
  • Inner tank thickness: 3.5mm, outer cladding thickness: 2mm
  • Surface treatment: Fine polished and brighted
  • Inner tank treatment: polished, roughness: 0.4 um
  • Cone top, cone bottom, Aluminum silicate insulation
  • Top fittings: Manhole with sight glass, light
  • 2 rotating spray balls inside
  • Side fittings: Thermowell, liquid level (optional)
  • Bottom fittings: mash outlet, gearbox & motor
  • Steam jacket on both cylinder and cone bottom
  • Separately controlled steam jacket
  • Jacket with safety valve
  • AISI 304 stainless steel leg, diameter: 114 mm, 4 pcs.
  • Motor brand: ABB, VFD controlled
  • Stir type: paddle type
  • Central venting pipe

2.000 liter Lauter tun 1 pcs.

  • Design pressure: Atmospheric
  • Material: AISI 304
  • Total volume: 2.860 liter, effective volume: 2.000 liter
  • Inner tank thickness: 3.5 mm, outer cladding thickness: 2 mm
  • Surface treatment: Fine polished and brighted
  • Inner tank treatment: polished, roughness: 0.4 um
  • Cone top, flat bottom, Aluminum silicate insulation.
  • Top fittings: Manhole with sight glass, light, warm water inlet
  • Side fittings: Thermowell, liquid level (optional), PT100 sensor
  • Bottom fittings: counter washing device, wort collecting pipe
  • Bottom spent grain door
  • Wedge wired filter plate, with the gap of 0.7-0.9 mm
  • Tank bottom with horn shape outlet for wort collecting
  • 2 Rotating spray ball inside
  • Coil pipe for sparging
  • Bottom square frame support size 100 mm x 100 mm
  • AISI 304 stainless steel leg, diameter: 133mm, 4 pcs
  • Motor brand: VFD controlled
  • Stir type: Shake and blade shape for better lautering effect
  • Central venting pipe

2.000 liter Kettle/whirlpool tun 1 pcs.

  • Design pressure: Atmospheric
  • Material: AISI 304
  • Total volume: 2.860 liter, effective volume: 2.000 liter
  • Inner tank thickness: 3.5 mm, outer cladding thickness: 2 mm
  • Surface treatment: Fine polished and brighted
  • Inner tank treatment: polished, roughness: 0.4 um
  • Cone top, cone bottom, 140-150 degree, Aluminum silicate insulation.
  • Top fittings: Manhole with sight glass, light
  • Side fittings: Thermowell, liquid level (optional), whirlpool inlet, PT100 sensor
  • Bottom fittings: draining outlet, thermowell, steam jacket
  • Rotating spray ball inside
  • AISI 304 stainless steel leg, diameter: 133mm, 4 pcs
  • Central venting pipe
  • 6% evaporation
  • Steam jacket on both cylinder and cone bottom
  • Two jackets on cylinder and cone part
  • Separately controlled steam jacket
  • Jacket with safety valve
  • Central venting pipe
  • Flat bottom with 1% slope
  • Tangent inlet at side place
  • Draining outlet at the lowest position
  • Two outlets at bottom of cylinder part
  • Steam condenser configured
  • Drain, wort draw-off, steam-jacket

Mash pump 1 pcs.

  • Material: S/S 304
  • Sanitary grade
  • Flow rate: 10 m3/h, lift height: 24m
  • With VFD control
  • Trip clamp inlet/outlet connection
  • Used for transferring liquid from mash tun to lauter tun

Lauter pump 1 pcs.

  • Material: S/S 304
  • Sanitary grade
  • Flow rate: 5 m3/h, lift height: 24m
  • ABB brand with VFD control
  • Trip clamp inlet/outlet connection
  • Used for transferring liquid from mash tun to lauter tun

Wort pump 1 pcs.

  • Material: S/S 304
  • Sanitary grade
  • Flow rate: 5 m3/h, lift height: 24m
  • With VFD control
  • Trip clamp inlet/outlet connection
  • Used for self recirculation or transferring wort from kettle/whirlpool tank to heat exchanger.

50L Buffer tank 1 pcs.

  • Material: Interior AISI 304
  • With sight glass for inspecting
  • Spray ball inside
  • Wort inlet outlet
  • Bypass for wort not going into buffer tank
  • Position: the same level with lauter tun filter plate
  • Function: Avoiding vacuum problem, protect tanks
  • Horizontal type with sight glass

Hopback 1 set

  • Material: AISI 304 S/S
  • Volume: 5 M3/h
  • Outer surface: mirror polished
  • Filter core inside, finess: 80
  • Triclamp connection with plate heat exchanger
  • Removable top lid, with venting valve
  • Pressure gauge installed for displaying inside pressure

Liquor blending unit 1 set

  • For mashing in and sparging
  • One mixing unit with two separate pipes to mash and lauter
  • Inline temp displaying
  • Inlet for cold and hot water
  • Thermometer installed at the inlet to mash tun
  • Flow meter can be configured for checking liquor inlet amount
  • System includes Thermometer, piping works for cold and hot water mixing, butterfly valve/ball valve for flow rate adjusting, check valve
  • Flow meter for controlling on/off valve

Material/wort/water/CIP Piping work 1 set

  • Material: AISI 304 S/S
  • Sanitary grade
  • Argon arc welding
  • Single welded, double shapped
  • Trip clamp connection with butterfly valves
  • Including pipes for mashing liquid, wort, cold/hot water and cleaning liquid transfer
  • Butterfly valves with 8 positions to control liquid flow.

Plate heat exchanger 1pcs.

  • High efficiency plate frame heat exchanger
  • Sanitary grade
  • Stage: Double
  • Triclamp connection
  • EPDM gasket
  • Pressure: 5 bar
  • With thermometer for checking wort temp
  • With aeration unit for oxygenation.
  • Designed as the exact data from actual brewing
  • Including: wort inlet/outlet, cold water inlet/outlet temp, flow rate etc
  • Efficient heat recovery to hot liquor tank
  • The second stage is for backup, in case customer use glycol for cooling.

Working platform 1 set

  • Material: AISI 304 stainless steel
  • Type: plate with hole
  • Skid proof
  • Handrails on platform and steps
  • Convenient working height for brew house tanks
  • Designed as actual building requirement
  • The control panel can be mounted on the platform or below it.

Steam piping line 1 set

  • Material: SUS 304, sand polished pipes
  • Pneumatic valve for steam flow control with stop valve
  • Pressure gauge, safety valve
  • Condensed water pipe
  • Condensed water can be connected together for reusing
  • Working pressure: 1 bar

Beer hose 2 pcs

  • Sanitary grade
  • Length: 9 meter a piece
  • Triclamp connections

Please note this is only the brewing unit. Heating, hot water system, electronic control fermenters etc. are optional.

Additional information

Weight 1 kg